8th Day - 16 July Monday

SETUP RFID DOOR LOCK ACCESS CONTROL

Today our supervisor who was Mr Mazran Bin Esro choose three persons to do this project. So, Saiful Amirin, Faris and Hanif have been chosen to complete this project so before we get started first we need to see Engineer Siva Kumar Subramaniam to take all the equipments which were RFID Access Control, RFID Cards and EM Block from him. We used model G2000-C RFID Access Control including the user’s manual to guide us through setting process for this project. Based on the user’s manual given we must find it on how to setup RFID Access Control, explore and learned the process by ourselves. There were three ways to configure how the user making contact with the RFID Access Control System which were keyfob entry, password entry, and keyfob plus password entry but for our basic learning process Engineer Siva Kumar Subramaniam just told us to configure the setup for keyfob entry and password entry only.

SPECIFICATION

Working Voltage ....................... 12V DC

Unlock current .......................... up to 1A

Static current ............................. up to 60mA

Reading distance ....................... 0 – 10cm

RF Type ..................................... EM 125kHz

Working temperature ............... -10°C to +70°C

Humidity range ......................... 10% to 90% non-condensing

Dimensions................................ 117 x 117 x 21mm

CONFIGURATION  JUMPERS

J1

This is used to select whether the lock is supplied power to keep it closed (NC), or is only      supplied power to open the lock (NO) Select (NO) for all 4tronix locks and releases

J2       

This is used to select a high voltage (12V) or low voltage (2V) for lock operation. This is supplied set to 12V and should be left like this for all 4tronix locks

S16     

This is only used to reset the master password. See following instructions. Leave connected between Pin1 and Pin2.

INSTALLING THE SYSTEM

1.      Connect 12V DC power to pins 1 & 2, observing correct polarity

2.      Connect the lock between pins 3 and 4

3.      Connect the normally open lock output from a Door Entry System or a door switch (or both) to pins 5 and 6

4.      If a door bell unit is required, connect to pins 7 and 8

CONFIGURING THE SYSTEM

A.  Entering & Exiting System Configuration mode

B.  Changing the master password

C.  Add new user (keyfob entry)

D.  Add new user (password entry)

E.  Add new user (keyfob plus password entry) F.   Remove one user

G.  Remove all users

H.  Set door open time

I.    Reset Master Password

A: SYSTEM CONFIGURATION  MODE

1.   Normal operation mode   

2.   Press the ‘#’ key   

3.   Then press the 5-key master password (default is 12345)

4.   Now in system configuration mode   

5.   In this mode you can perform all the configurations you need, without exiting the mode

6.   To exit configuration mode, either wait 15 seconds without pressing a button, or press ‘#’ key again   

B: CHANGING  THE MASTER PASSWORD

1.   Enter system configuration mode (see A above)

2.   Press 1  

3.   Enter new 5-key password (eg. 32561)   

4.   New master password is accepted

C: ADD NEW USER (KEYFOB ENTRY)

1.   Enter system configuration mode (see A above)

2.   Press 2

3.   Enter the 4 digit unique User ID   

4.   Place user’s keyfob near the keypad      Buzzer sounds once

5.   New keyfob user has been added

6.   If the buzzer sounds three times and lights return  then the user was already logged into the system. Try deleting the user, then re-adding

7.   If the buzzer sounds four times, then the memory is full and all

250 possible users are stored. You must delete some users first before adding new ones.

D: ADD NEW USER (PASSWORD ENTRY)

1.   Enter system configuration mode (see A above)

2.   Press 2 

3.   Enter the 4-digit unique User ID   

4.   Enter the 6-digit user-specific password     Buzzer sounds once

5.   New password user has been added

6.   If the buzzer sounds three times and lights return to  then the user was already logged into the system. Try deleting the user, then re-adding

7.   If the buzzer sounds four times, then the memory is full and all

250 possible users are stored. You must delete some users first before adding new ones.

E: ADD NEW USER (KEYFOB PLUS PASSWORD ENTRY)

1.   Enter system configuration mode (see A above)

2.   Press 0     

3.   Enter the 4-digit unique User ID   

4.   Place user’s keyfob near the keypad      Buzzer sounds once

5.   Enter the 6-digit user-specific password     Buzzer sounds once

6.   New password user has been added

7.   If the buzzer sounds three times and lights return to  then the user was already logged into the system. Try deleting the user, then re-adding

8.   If the buzzer sounds four times, then the memory is full and all

250 possible users are stored. You must delete some users first before adding new ones.

F: REMOVE ONE USER

1.   Enter system configuration mode (see A above)

2.   Press 3     

3.   Enter the 4-digit User ID to delete  Buzzer sounds once

4.   User is removed

G: REMOVE ALL USERS

1.   Enter system configuration mode (see A above)

2.   Press 4    

3.   All users are removed

H: SET DOOR OPEN TIME

1.   Enter system configuration mode (see A above)

2.   Press 5     

3.   Press 2 keys for door open time in seconds. So, for the lock to remain open for 5 seconds, enter  then     

4.   Door open time is changed

I: RESET MASTER PASSWORD

1.   Remove power from the KeyPad

2.   Move S16 jumper to pins 2 & 3

3.   Replace power to KeyPad  Beeps constantly

4.   Remove power from KeyPad

5.   Move S16 jumper back to pins 1 & 2

6.   Replace power to KeyPad

7.   Master Password is reset to 12345

source from:

RFID Access Control System Configuration pdf